7835-10-2005 7835-10-2004 Monitor Display Panel for KOMATSU Excavator PC160 PC200 PC228

7835-10-2005 Monitor Display Panel for Komatsu PC200-7 and PC228US

The 7835-10-2005 monitor display panel is supplied for Komatsu excavator cab electrical system repair. It is commonly searched as 7835-10-2005, 7835102005, 7835-10-2004, 7835102004, monitor display panel, cab display monitor, gauge display or excavator monitor for Komatsu PC160-7, PC200-7, PC220-7, PC228US, PC270-7, PC300-7, PC350-7, PC400-7 and PC450-7 excavator references.

This page focuses on 7835-10-2005 as the main part number. 7835-10-2004 can be used as an important reference number, while 7835102005 and 7835102004 are no-hyphen search formats. Final fitment should be confirmed by the old monitor number, front panel layout, rear connector type, plug position, mounting points and machine information before ordering.

Machine Reference for Komatsu Excavators

Common machine references for this monitor display panel include Komatsu PC160-7, PC200-7, PC200LC-7, PC210-7, PC220-7, PC220LC-7, PC228US, PC228USLC-3, PC270-7, PC300-7, PC350-7, PC400-7 and PC450-7 excavators.

Machine model alone is not enough for final confirmation. Komatsu monitor panels may vary by serial number range, wiring harness, connector layout, software version and cab configuration. The old monitor label and rear connector photos are more reliable than the model name alone.

For accurate ordering, compare the removed monitor with the replacement unit before shipment. Photos of the front screen, rear label, connector side, mounting area and machine nameplate are useful for confirmation.

Part Number and Reference Notes

7835-10-2005 is the main part number of this product page. It should stay visible in the product title, top parameters, first paragraph, product body and image ALT text.

7835-10-2004 is an important reference number for this Komatsu monitor display direction. It should support the main 7835-10-2005 signal rather than replace it as the primary page focus.

Nearby Komatsu monitor numbers such as 7835-10-2002 and 7835-10-2003 should be treated as checking references only unless the old monitor label or supplier data confirms interchange. Similar monitor panels can vary by connector position, screen layout, software version and machine configuration.

How to Confirm the Correct Komatsu Monitor Display Panel

Excavator monitor panels can look similar from the front, but small differences in rear connector, plug quantity, display layout, warning icons and mounting position may affect installation. Before ordering, compare the removed monitor carefully.

• Confirm whether the old monitor number is 7835-10-2005, 7835102005, 7835-10-2004 or 7835102004.

• Check whether the machine is Komatsu PC160-7, PC200-7, PC210-7, PC220-7, PC228US, PC270-7, PC300-7, PC350-7, PC400-7 or PC450-7.

• Compare the front panel layout, screen area and button arrangement.

• Check the rear connector type, plug quantity and pin layout.

• Confirm mounting holes, bracket position and installation space.

• Send photos of the old monitor front side, rear label, connector side and machine nameplate before quotation if you are not sure.

Common Monitor Failure Symptoms

A monitor display panel may need replacement when the screen is black, dim, flickering, cracked, unreadable, shows missing display areas, cannot show warning information, has button failure or does not respond normally after power-on.

Before replacing the monitor, check the power supply, fuse, ground wire, connector, harness condition and controller communication. Some display faults may be caused by wiring or power issues rather than the monitor itself.

If the old monitor was damaged by water, corrosion, unstable voltage or short circuit, the root cause should be corrected before installing the replacement monitor. Otherwise, the new display panel may fail again.

Installation and Testing Notes

Before installation, turn off the machine power and inspect the old connector. Do not force the plug into the new monitor if the connector shape, pin layout or mounting position is different.

After installation, power on the machine and check whether the monitor starts normally, displays machine information, responds to buttons and shows warning indicators correctly.

If the monitor powers on but does not show correct machine data, check the wiring harness, controller communication and machine version before assuming the monitor is defective.

Buying Notes for Repair Shops and Parts Distributors

For repair shops, this 7835-10-2005 / 7835-10-2004 monitor display panel is suitable for Komatsu excavator cab electrical system repair when the old monitor is damaged, unreadable or unable to display machine status correctly.

For parts distributors, it can be supplied as a Komatsu excavator monitor reference for PC160-7, PC200-7, PC220-7, PC228US, PC270-7, PC300-7, PC350-7, PC400-7 and PC450-7 service demand. Topvelsun supports small repair orders and bulk inquiries. Please send the required quantity, old monitor number, machine model, serial number and photos of the old monitor from multiple angles.

FAQ

What is the main product on this page?

This page is for the 7835-10-2005 / 7835-10-2004 monitor display panel used for Komatsu excavator cab display system repair.

Is 7835102005 the same search reference as 7835-10-2005?

7835102005 is the no-hyphen writing format of 7835-10-2005. Buyers may search either format, so both formats can be kept on the page.

Can 7835-10-2004 be used as a reference number?

Yes. 7835-10-2004 is an important reference number for this Komatsu monitor direction. The old monitor label and connector should still be checked before ordering.

Which Komatsu models are the main references?

Common references include Komatsu PC160-7, PC200-7, PC200LC-7, PC210-7, PC220-7, PC220LC-7, PC228US, PC228USLC-3, PC270-7, PC300-7, PC350-7, PC400-7 and PC450-7 excavators.

Can I confirm this monitor by machine model only?

Machine model is useful, but it should not be the only fitment proof. Please also check the old monitor number, front panel layout, rear connector, plug quantity, mounting holes and machine serial number.

What should I send before ordering?

Please send photos of the old monitor front side, rear label, connector side, plug shape, mounting bracket and machine nameplate. These photos help confirm whether 7835-10-2005 / 7835-10-2004 is the correct monitor.